[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Power Supply Mods Kit (was Re: Apple IIgs upgrades)
Jeff Tacy writes ...
>
> Hi all, does anyone here remember the Mac SE upgrade kit that included
> 18-ga wire, a bunch of new caps and other fun stuff, that increased the
> computer's amperage and allowed more upgrades, also fixed many problems?
> Is there anything like this for the Apple IIgs that someone has
> constructed? ....
Okay; here is your very own
A2-2000 On-Line Power Supply Mods Kit!
Swapping-in fat leads is, technically speaking, a pretty simple job.
You pop out the power supply, open it, unsolder old +5, +12, and Ground
leads, solder in the new leads, close and replace the power supply. The
tricky part is what hackers call the "mechanics".
First, #12 or #14 gauge wire is not very flexible. Getting stranded
wire (instead of solid) helps. Probably, #14 gauge is more than fat enough
for all three leads. One case where #12 or #10 gauge may be worth the extra
trouble is the +5V lead.
Use wires colored the same as those you replace. On the standard
connector, the first two leads are Ground. Almost always, these are black.
Next, there is a space, then, in order +5, +12, -12, -5.
Depending on the bother involved, you can unwedge the wire bundle
where it passes through the supply case and remove the three old wires
(+5V, +12V, and one Ground wire). Or, you can just cut away each old lead.
Leave the -5V and -12V leads and one Ground lead alone.
Getting to the PS circuit board involves some work. After removing the
mounting bolts, you will have to scooch up the board in order to get to the
bottom side. This will be easier if the wire bundle has been unwedged.
Another hurdle is soldering to the circuit board. Once the old leads
and excess solder are removed, you will probably find that the holes are
too small! A jeweler's screwdriver makes a good hand drill for enlarging
holes. (Drill from the circuit side. Be careful not to tear or dislodge the
printed circuit.)
The new leads should be routed through the unused fan slots. (If a fan
is attached, remove it. It's in the wrong place to do much good in cooling
your GS.)
Note: If you have a fan mounted to the PS and you wish to keep it, then, it
will be necessary to enlarge the original cable exit hole. A sheet metal
"munching" tool should let you do this without having to entirely remove
the PS circuit board. (Just be sure to catch all of the munched pieces!)
When routing the leads be careful not to place a twisting force on a
lead where it is soldered to the circuit board.
To get to each spronger (contact) in the plug, press on it through the
slot on the side near the wire end. This pushes up a small retaining tab so
that pulling on the attached lead will pull out the spronger.
Cut off the old lead, clean the end, and solder on the new lead. Press
the spronger back into the plug. To avoid mixups, it's best to complete the
process for each lead before doing the next.
When plugging in the power supply, take time to shape and arrange the
wires to minimize stress on the motherboard.
Motherboard Mod
Fatter +5, +12, and Ground leads should protect you power supply and
reduce circuit noise.
If audio noise in your stereo card output and/or system bombing due to
noise glitches were problems, they may be eliminated. A lot depends upon
which cards you've installed, which slots they are in, and whether your
IIgs is a ROM-01 or ROM-03.
The motherboard circuit traces supplying power to each Slot are fairly
skimpy, especially on ROM-01 boards. A heavy power user in Slot 7 can
produce significant noise up and down the entire Slot 'backplane'.
The cure is to remove the motherboard and run leads to a couple Slots
...
First, flip over the motherboard and get oriented. Below is a quickie
sketch showing the Power Connector points as well as key power pins for a
Slot. The view is from the _Bottom_ with the _Back_ of the motherboard
facing you:
Bottom of Motherboard
Power Connector Socket Slot
X GND +12V (pin 50) X X (pin 1)
X GND X X
.
X +5V .
X +12V .
X
X X X
GND (pin 26) X X (pin 25) +5V
.... Ground Plane Area (plug shields, etc. connected here) ....
|
|______________ Back Edge of Motherboard _________________________
A good way to make sure you know what's where is to use an Ohm meter
to check Resistance from pin 26 (GND) to a metal plug shield near the back
of the motherboard. (Set your meter to Ohms X1. Touch one meter lead to pin
26 and the other to a metal plug shield. Resistance should read nearly
zero. Reverse the leads and repeat the check. Again, Resistance should read
nearly zero.)
Repeat the check for R between pin 26 and the GND points on the Power
Connector socket. R should be nearly zero. Using a marker pen or white-out,
mark pin 26 (GND) on Slots 3 and 7. Also mark the GND points of the Power
Connector socket.
GND: On the bottom side of the motherboard, connect a Black #16 gauge wire
from one of the Ground points of the Power Connector socket to the Ground
plane area near the back of the motherboard. Run a short Black #16 gauge
wire from pin 26 of Slot 3 to the Ground plane; run a short Black #16 gauge
wire from pin 26 of Slot 7 to the Ground plane. (You may need to scrape
through green insulating lacquer to solder to the Ground plane area.)
+5V: On the bottom side of the motherboard, connect two #16 gauge Red wires
to the +5V point of the Power Connector socket. Connect the other end of
one +5V Red wire to pin 25 of Slot 3; connect the other end of the second
+5V Red wire to pin 25 of Slot 7.
+12V: If you have any cards which are likely to draw heavily on the +12V
line, then, on the bottom side of the motherboard, run a #18 gauge White
wire from the +12V point of the Power Connector socket to pin 50 of the
Slot in which the card is normally located. Otherwise, just run an #18
gauge White wire from the +12V point of the Power Connector socket to pin
50 of Slot 7.
Check your connections. One quick check is that the GND and +5V wiring
to Slots 3 and 7 should be Black, Red (moving left to right) and Slots 3
and 7 should 'look the same'. Any +12V wire should be on the same side of
the Slot (i.e. the same column of pins) as GND. None of the wires should be
connected to a middle pin on any Slot.
Notes:
1. All wires are insulated.
2. When cutting wires, allow enough slack to permit routing each wire. You
want to avoid having a wire rest against pointy connections on the
motherboard. Route wires away from motherboard mounting holes and around
places where the bottom of the case supports the motherboard.
3. The case's bottom and back metal shields are something of a shorting
hazard. Replacing the motherboard is much easier if these shields are
popped out and ditched.
Once everything checks out, replace the motherboard taking care that
no wires are caught between a support point and the motherboard.
Rubywand